Now You See it, Now You…Wait! Where Did it Go?

It used to be that the only things certain in life are death and taxes. I’m going to add a third thing: someone wants your backflow. Not in the manner of “I want to buy Girl Scout cookies.” This is in the line of “I want to steal that backflow and sell it for money.” Someone is looking to you to pay their bills. After all, charity starts at home. Your home, your backflow, your expense.

Three things are combining to cause trouble. The economy is down, which means unemployment is up. Besides the standard, everyday crook, people who would never consider theft before now turn to it to pay bills. The second thing is continuing global population growth. More people means more resources are needed to support them. That means metal for tools. The final thing is the growth of formerly agricultural economies into modern, technology driven countries. Technology requires metals of all sorts. Roll all this together and prices for scrap metals are high and rising. Your backflow is worth noticeable money to someone.

You lose in two ways. The most obvious is you have to pay to get the backflow replaced, parts and labor. The second is the water you have to pay for when they steal the backflow and your system starts pouring thousands of gallons out to the street. Not to mention the inconvenience of going without household water if you don’t have a cut off valve on your system. The best thing to do is stop the theft from ever happening.

One way is to use the Jedi mind trick: “you only thought you saw a backflow here…you are obviously wrong…there is no backflow here…” This trick works best if you supplement it with a Dekorra rock enclosure. These are fake boulders designed to cover your backflow and make it blend into the landscaping. Who notices a rock? There’s not a lot of demand for stolen boulders. The enclosures cover the backflow, are available in standard, insulated and heated options, two finishes and a multitude of sizes. Since rocks are used in landscaping already it doesn’t scream out “hidden backflow.” It says “landscaping feature.”

If you want the cover and/or insulation but aren’t a Jedi you can use the standard backflow enclosure. They provide the same weather protection as the rock enclosures without the camouflage effect. They do add the option of a side grid for quick visual inspections.

These also add one more step to getting to your backflow. This adds time and your average thief wants a short, quick job. Adding time discourages theft.

If adding time and effort discourages theft, then the other option is making the backflow very hard to get. Use the Gorilla Cage. Sounds like a visit to the zoo, doesn’t it? Except this cage keeps animals (crooks) out and peace and serenity in. The cage is made of strong steel tubing, angle and expanded metal with a guard to prevent the padlock from be cut by bolt cutters. Notice how the lock guard completely surrounds the lock? You don’t The cage is bolted down to a concrete pad making for strong unitized construction. The form is even provided with the cage. Once unlocked they allow easy access for servicing or testing of the back flow.

No one will open these with a simple hammer or hacksaw. Bolt cutters won’t work. A cutting torch will but that’s a little more obvious than crooks want to be. Most crooks will pass these by and go to the next unprotected backflow they can find.

Whether you protect your backflow by hiding it or locking it away, the important things is that it stays in your yard, not someone’s truck.

Apr 16 2012

Designed to Fail? Ooops…

If you are old enough you remember the Pinto. New Coke? The Newton? Zune? Mars Needs Moms? Trying to cover all bases here. These are all products that failed due to poor design. The strange thing about a good design is you don’t notice it. A bad design slaps you in the face, causes trouble, often costs money and talks bad about your dog.

Ok. Irrigation designs don’t talk about your dog but a bad one will cost you time and money, along with increasing your stress level. Dry spots, swamps, water runoff, irrigating your neighbor’s yard and watering in the rain are all problems caused by bad design. To quote someone, somewhere “It don’t ever have to be that way no more never.” (I put the ‘never’ in to cancel the double negative.)

Irrigation planning is involved and challenging and simple and logical. The great thing about residential planning is so much of the work is done for you and there are companies that will do it absolutely free. They send you a drawing, instructions and a parts breakdown. If you want to go that route check out Rain Bird and Toro.

If you want to design your own Hunter has a very good guide. There are countless references and books available and all the math has been worked out. The answers are in a chart somewhere. Check here for a sample. At first glance you may get dizzy, but don’t worry, the numbers make a lot of sense once you start designing a system.

Whichever system you use, make sure you mark and consider all trees, fences, storage sheds, etc. You can’t blame Rain Bird if you forget to tell them about the pool.

If you decide to have a professional design your system, which I strongly recommend, be sure to check their credentials. In Texas you must be licensed to charge for a system design. In other states you must either be a licensed irrigator, a licensed plumber, or a licensed architect. Some states don’t have any restrictions on who can design a system. That makes it tough. Ask for references. Ask to see their work. As a professional I’d be glad to let anyone see any system I’ve ever designed. They should be also. If not, something is wrong.

A good design should have a drawing showing you the locations of the spray heads, the piping, the controller, the backflow, the valves and the areas covered by each head and the flow.

In this sample you see the spray head location, the radius and pattern (10H= 10 foot radius, half circle, Q = quarter), zone number, size of pipe (1”) and gallons per minute. The pipes are shown, coverage is shown and the valves are located.

Very important: a good design will also include a parts list of all pipes, fittings, heads, wire, valves, etc. Do not accept a design that does not.

Now for the hard part: when you have a good design, follow it. Don’t decide in the field that digging 3 more feet is just too much effort. People get tired and figure anywhere in the general area is close enough. It’s not. You’ll realize that before too long. Digging is hard work. Lots of digging of little trenches is real high on the “I’m sick of this” list. Keep telling yourself “the shovel is my friend. The shovel is my friend…”. It will be well worth it when that good design lets you forget all about it as your lawn and gardens flourish and you save money with efficient water usage.

Apr 3 2012

Valve Manifolds and Why You Want Them

Think about your average irrigation system. Say five zones made up of spray heads and rotors. Front yard, back yard, side yard. Pretty much what you see everywhere. This means that there are five valves in the system. Now, there are two ways you can install valves. Both work. You can install them in each zone, as illustrated:

This works fine but someday, when you need to find the valve for repair, it may be overgrown, have a dog house on it or have simply disappeared. Plus you are spending money on seven valve boxes and all that wire to go to all those valves.

This is another way to place your valves. This keeps all the valves in a simple to find and maintain area and you would only need two valve boxes. This is called clustering. It makes long term maintenance far easier. You can also cluster them in out of the way, low traffic areas, minimizing risk of damage.

The easiest way to install this is with pre-made manifolds. Two of the most popular are the Action Machine and Dura brands. They are both available in different sizes and are expandable for future growth.

So what’s the difference? Why is one labeled Premium and one Standard? There are two main differences. The first is the pressure rating. The Premium has a pressure rating of 235 psi @73^o. The standard has a rating of 150 psi. Again, either will work for the vast majority of installations.

The second difference is more practical. Understand that once these are installed you don’t touch them again until something goes wrong, usually years down the line. At that time they will be dirty, wet, muddy and possibly underwater. Now you want anything that will make it easier to work on the system. The Action Machine coupling has a much larger and more defined grip on the ring. The larger grip makes a world of difference when it’s wet and slippery. Saves time, skin and frustration.

Either manifold will work fine. You might wonder at this time why you can’t just build your own. After all, PVC is cheap and you will be working with it already. No reason you can’t and it will work. However, the premium manifolds are made of Schedule 80 PVC, much stronger than the Schedule 40 you will be working with. Add the fact that the manifold backbone is one piece and you gain both rigidity and a guaranteed straight line. Finally, the time and effort you spend measuring, cutting and gluing your parts together is worth something. Save that time for relaxing after the job is done. Pre-made is best by far.

MORE INFORMATION

For any irrigation system questions please visit us at Sprinkler Warehouse.

Mar 27 2012

Why Just Florida?

What does Florida know about irrigation that the rest of the country doesn’t? Why do they use more of a surprisingly simple and effective device than any other state? Especially when you consider how much money this device can save? Do I sound like a late-night infomercial yet?

Take a look at the K-Rain Indexing valve. This valve lets you irrigate up to six zones without installing and wiring six different valves. Each time the waters turns off and back on the valve waters a different zone. There is a really smart disc inside that advances to the next zone when pressure drops. Water zone one, stop water for a few moments, start water, water zone two, etc. Automatically.

Yes, it looks strange. We don’t care: it works great. These are commonly installed either on a direct feed from a pump or downstream of a single solenoid valve. The way it works is simple. Say you are using a solenoid valve. The valve comes on. Zone one on the index valve opens and water goes to zone one. The solenoid valve turns off. The index resets to zone two. The master valve comes on, zone two waters. Repeat for three through six. These are available with either four or six outlets; a six outlet is shown.

If you are working off a pump then each time the pump cycles the valve advances. This completely eliminates the need for a solenoid valve and the related wiring and controller. These valves work with flows as low as 10 GPM and at pressures of 25 to 75 PSI.

A great feature is the possibility of future expansion. Say you only have two zones but plan on expanding. You can get the four outlet model with a two zone cam. Down the line you can change the cam out to allow for three or four zones. Just keep the two future outlets capped off until then. The four zone outlet pattern is shown; the six zone is similar.

Here we have one valve that eliminates the need for any solenoid valves if working directly off a pump and eliminates the need for all but one if working off a municipal system supply. No wonder Florida loves it. Money saved on valves and money saved on wiring. Labor saved by not installing the other valves and wiring. Labor saved = money saved. Order now. Operators are standing by. Or the website is, anyway. And if you order in the next 10 minutes you’ll have plenty of time to do something else today! So hurry!

Mar 16 2012

The Right Way to Assemble and Glue PVC Pipe

There are many ways to glue PVC pipe and a number of solvents. The bright side is most of them will work. The down side is many of them won’t, wasting time and money, or only appear to work until the pipe is long buried. Then it becomes expensive.

We are going to discuss measuring, fitting and gluing pipe. The premise is that if you do it correctly you only do it once. Not to mention limiting trips to the hardware store and controlling blood pressure.

Before we do anything else, there are two warnings. One on safety, one on product performance.

Folks, these are harsh chemicals. Don’t get them on your skin. Definitely don’t get them in your eyes. No breathing fumes. Make sure you have plenty of ventilation, as in ‘do it outside’. Wear gloves. Wear eye protection. Care to guess what the cement does to plastic contacts or your expensive glasses?
There is such a thing as too much glue. This is not Elmer’s Paste. If you put too much cement on and it has a chance to puddle it can and will eat through the pipe or fitting. Now you have a hole in the fitting. Also, too much glue when attaching valves can drip into the valve body and cause failure.

First, get these things together:

Rags
Primer and cement
Something to put the pipe on while you cut (sawhorse, cinder block, table, etc.)
Gloves
Hacksaw
Marker or crayon
Rough file or course sandpaper

Optional but you should have

Miter box
Pipe cutter, preferably ratcheting type though standard will work fine.
Hammer/Channel Lock pliers

Measuring is the shortest part of this paper. Remember that you have to include the length of pipe that goes into the fitting and the length of the fitting. Say you have a 10’ section from corner to corner. The fittings add length. You need to figure out how short to cut the pipe so you can add the fittings and still get 10’. How far does the pipe go into the fitting? Depends. Depends on the cut, the pipe, your strength. There is a stop designed into the fitting. How far in is it? To find out, take the pipe and fitting, get them wet with water only, and push the pipe into the fitting with firm but not killer force. The water makes it easier to slide them together. Now take a pencil and mark the pipe at the edge of the fitting. Twist the pipe back out. The distance from that mark to the end of your pipe is your glue area. This can vary depending on fittings and pipe size. Measure everything twice. Write it down.

Cutting the pipe is more important that people realize. The cut should be square and smooth. If you don’t cut it square the short end will not make complete contact with the inside of the fitting and will not bond as it should. It helps to use a miter box, if you can, or good ratcheting cutters. Take your time. It will help avoid problems later.

Ideally the end of the pipe should be smooth with tapered edges. Now I know you don’t hear many people talking about tapering a PVC pipe edge. You’ve probably never seen it and I know many professionals that have never even heard of it. However, we’re discussing the correct way to do this. You can bring in the shortcuts when I’m not looking. If you have a simple square cut pipe it has a tendency to push the cement ahead of it, as in the drawing. A smooth pipe with an edge taper lets the cement flow between the two. So take your file, file off the burrs that are left from the cutting, if any, and add a quick taper to the end. At the very least use sand paper to smooth the edges and take off any burrs.

On to fittings. Once you have your pipe cut do a practice assembly. We do this to make sure we don’t glue the elbow on facing the wrong direction. Lay the pipe out along the trenches. Put the elbows, Tee’s and 45’s on just as if you were putting it in the trench. Once you are sure it is correct draw a line on the fitting and pipe with a marker or crayon. This will help line it up for you when the cement is on and drying fast.

Ok. Pipes are cut, fittings are ready. Now time for primer and glue. First I’d like to clarify one thing. It’s not really glue or cement. It’s a solvent. The solvent basically melts the PVC. When two pieces of PVC are joined using PVC cement the plastic melts, molecules blend, and it re-solidifies to a single unit. That’s a gross simplification of what happens but its close enough. When the cement is through and the PVC has re-solidified it is now the strongest piece. If you do it right the fitting or pipe will break long before the joint.

The first thing you do is make sure the pipes and fittings are dry. There are some cements that don’t need primer and will work with a wet pipe but we tend to avoid them. First, using primer gives us a last chance to check the pipe. You’d be surprised how often a small crack will hide until the primer hits it. . The other reason is that special cement tends to set FAST. Real fast. No room for error or hesitation. Why ask for trouble?

Now prime both the pipe and the fitting. Use just enough to do the job. Too much doesn’t gain you anything. Using the included dauber wipe the glue area of the pipe and the glue area of the fitting with primer. Since it’s purple it’s easy to keep track. By the way, it stains everything so be careful. Primer removes dirt and grease and preps the PVC. When PVC is formed it has a hard, clear coating on it. This is resistant to the cement. Primer removes the coating, exposing the PVC.

Now apply the cement to both pieces. Do the fitting first. Since the cement is inside you can lay it down for a moment while you coat the pipe. Once both are done push the pipe into the fitting, turning about ¼ to ½ turn as you go. This makes sure the cement spreads evenly. Hold it together for about 15 to 30 seconds. Because of the chemical reaction and the way the fittings are formed there is a tendency for push back. The pipe will want to come out so hold until is sets. If you’ve done everything correctly you can look around the edge of the fitting and see a little glue bead that has been push out by the fitting. It should be continuous. A gap might mean a pinhole leak later. Wipe off any excess cement.

I know. I didn’t say what you did with the pliers or hammer. That’s ok. They are always good to have.

That’s it. Doing takes far less time than reading about it. Doing it correctly doesn’t add any time and sure can save you a headache in the future.

Mar 13 2012

Watering Trees

Trees clear the air, provide homes to wildlife, offer shade for picnics, and, without trees, there would be no tree houses or tire swings. They also add value to your dwelling, increasing the visual appeal and adding to the livability of your home. Trees are a vital part of our lives, directly and indirectly.

The drought that hit the United States has damaged or killed millions of trees. Texas has been particularly hard hit but the damage extends from New Mexico to Florida. By one estimate, Texas has lost approximately 500 million trees, with other states suffering various levels of damage. Unfortunately, the drought is predicted to continue through 2012.

The question then becomes: what is the best way to water a tree? Ideally, the method chosen will provide the greatest amount of benefit to the tree while using the least amount of water. The first thing to know is where to water your tree. Watering directly at the trunk is not only a waste of water but can promote some diseases. There are a few simple guidelines to follow for established trees.

First, the water needs to get to the roots. Watering too little, or just surface watering, will cause shallow roots, weakening the tree and leading to more drought damage. Deep watering to about 10” to 18” inches below the surface is best, depending on tree size. The older, more mature tree the deeper you should go.

For most trees, irrigate within the drip line. The exception is evergreens, as they tend to grow up and not out. For these, imagine the drip line to extend a couple of feet outside the physical drip line.

This Drip Line is basically the furthest most extent of the leaves, as shown in the picture of the tree. Inside this area is where the plant is growing smaller roots known as Feeder Rootlets. These absorb moisture and nutrients from the soil.

The objective is to water slowly, dispersing the flow of water to get the water deep down to the trees roots.

Don’t dig holes in the ground in an effort to water deeply. This exposes the roots to air and dries out roots even more. Watering at ground level with a sprinkler system does help. However, running your sprinkler system long enough to provide sufficient water for trees would result in a great waste of water in other areas and increase chances for water runoff.

There are a number of ways to provide water at the proper rate and in the proper place, saving both the tree and water. The first, and simplest, is through the use of soaker hoses. Simply place rings within the watering area and turn the system on. The water goes where it is needed with little waste. The disadvantage is the labor involved in placing the hose, turning it on and off, removal and replacement for mowing and raking, and the possibility of damage to the hoses, requiring replacement. While efficient in water placement this method does require a bit of effort.

A more efficient method is the use of deep watering systems. One system involves using tree watering stakes. These range in lengths from 14” to 36”, connect to your watering system, either drip or garden hose, and put the water where it can be best utilized. This way the roots are sure to receive the water without worry of wind or run off.

Finally, there is a root watering system that attaches directly to your irrigation system. These provide the needed water and have minimal visual impact on the yard, as they are installed at grade. Since they are attached to your irrigation system you have the ability to set the watering schedule as needed without the frequent labor needed with soaker hoses or garden hose attachment.

Whichever system you choose, the key to tree survival is proper watering. Too much, too little or watering in the wrong place can cause further harm to the tree. Proper watering can extend the life, health and beauty of the tree for years to come.

For more information about anything involving irrigation, please visit us at www.SprinklerWarehouse.com.

Mar 5 2012

How to Identify the Size of the Water Meter & Supply Line

A critical step in designing an efficient irrigation system is determining how much water you have available, its flow and pressure. Start at the meter. It is usually near the curb buried in a meter box.

To find the meter’s size first look at the dial. Many meters have their size located directly below the gallon count. Sometimes it is stamped on the metal below the dial face. It will be something like ¾” or 1”, in most residential cases. Sometimes it’s not there or so dirty you can’t find it. In that case you have two choices. The easiest might be to simply call your water company and ask. They’ll have it on record. The other option, which is far from accurate but is safe for design, is to determine the size of the pipe leaving the meter and assume the meter is one size smaller. It is fairly common for the meter to be one size smaller than the feed pipe to the house. Typical water meter sizes are: 5/8″, 3/4″, 1″, 1 1/2″.

If you can’t read the pipe size on the pipe leaving the meter, don’t worry. DON’T GUESS. Also, don’t lay a ruler across it and use that measurement. If you have PVC you might be lucky enough to see the size printed on the pipe. If not, or if it’s not PVC, we have to measure. First, find a piece of string. Now, wrap the string around the pipe and mark the point where the string crosses. The length between the marks gives you the pipe size.

Pipe Size Conversion Chart- Nominal Pipe Size to Circumference
Nominal Pipe Size	Approximate String Length in Inches
	Copper Pipe	Galvanized Pipe	PVC Pipe
½”	2″	2⁵⁄_8″	2⁵⁄₈“
⁵⁄_8″	2³⁄₈“	N/A	N/A
¾”	2¾”	3⁵⁄₁₆“	3⁵⁄₁₆“
1″	3½”	4¹⁄₈“	4¹⁄₈“
1¼”	4⁵⁄₁₆“	5³⁄₁₆“	5³⁄₁₆“
1½”	5¹⁄₈“	6″	6″
2″	6¾”	7⁷⁄₁₆“	7⁷⁄₁₆“

It is important to know what your pipe is made of. PVC tends to be white or grey (usually white), sometimes with lettering on the side and is plastic.. Steel grey and is magnetic, so that’s a quick test if there is any doubt. Copper will turn to a dirty green color over time and is not magnetic. Its connections will be soldered, so if you see silver at the joints you have copper. You may have what is commonly known as “flex” tubing. It can be either PEX or PE Tube. Pex is the stronger of the two and would usually be the one used for supply lines. It is white, might have PEX on the side. If there is any doubt then take a section to your supply house to see what you have and what fittings fit.

Now that you know what size meter you have we need to determine flow. That’s coming soon. Stay tuned.

Mar 5 2012

Want to Have an Impact?

Which came first: the lawn sprinkler or rain? Well, rain. Then lawn sprinklers. Well, no, I guess flooding and then maybe ditch irrigation and then someone poured water from a pot onto plants and …never mind. I’ll just skip ahead.

Brass Impact Rotor The impact rotor sprinkler was the first successful, efficient area sprinkler developed. The original design came about in 1933 from a farmer looking for a more efficient way to irrigate his citrus crop. Pouring water out of a pot just wasn’t doing it. It would not be an exaggeration to say this sprinkler revolutionized agricultural irrigation and is still an integral part of irrigation today.

One of the indicators of a good design is to look at how much something has changed through the years. A 1925 pickup had a drop tail gate, stake pockets, leaf springs, and was available with an 8’ bed and 1 ton rating. Sounds a lot like current pickups. If you saw the first impact sprinkler you would see that the design has changed little through the years. Arm still swings, it still rotates and it is still dependable. It would work fine today.

Impact rotors work best on large, open areas. Typical operating distances are from a low of 20’ up to 65’ in the residential applications and over 100’ in commercial uses. They provide consistent, dependable coverage with little maintenance required. Most give you rotation settings of a partial circle from 20°-340° or full 360° coverage.

What are the main advantages? There are a couple and they are important. The first is that the water path is uninterrupted. On standard, non-popup, rotors it doesn’t go through any filters or screens; it flows through just like the water from the end of a hose. This means the impact sprinkler is far less susceptible to clogging from debris. It also means there is very little risk of damage from grit and sand in the system. It just blows out.

The second is the exposed operating mechanism. With more modern design popup rotors there is an internal gear drive mechanism. This is vulnerable to dirt or debris in the water and can cause the rotor to stop turning. At this point the rotor must be disassembled to clean. With the drive mechanism of the impact being 100% external and with no gears to worry about, the durability and long term performance of the unit is greatly enhanced.

Pop-Up Impact Rotor One objection to impact sprinklers was their high visibility even when not being used. The Rain Bird Maxi-Paw acts as a pop-up, disappearing when not in use. It gives you the benefits of an impact rotor with the visual appeal of disappearing pop-up. One big advantage of these is you can use them to efficiently water a park or public area yet avoid trip hazards.

Impact sprinklers are thought by some to be ‘old technology.’ After all, numerous new and different irrigation products have come along since. Well, hammers are pretty old technology and no one hesitates to use them. Old doesn’t mean useless. The technology might be old but the usefulness and efficiency has increased through the years. With different sizes, replaceable nozzles, pop-up designs and water saving features the impact rotor looks to be around for a long time. It just works.

Mar 5 2012

Teflon Tape and How To Use It

Teflon Pipe Tape Teflon® tape (polytetrafluoroethylene, or PTFE), AKA plumber’s tape, is a thin film used to seal pipe threads. The tape is durable, flexible, and fills in the minor imperfections in the threads to seal leaks.

To use, hold one end of the tape against at the start of the pipe threads/end of pipe and start wrapping opposite of the direction of the threads, keeping the tape flat. Pull the tape Wrapping Pipe with Teflon Tape tightly into the threads but not so tightly that the threads cut through. Keep going in a flat uniform manner until you come to the ends of the threads/pipe. Now thread the pipe in carefully and you’ll have a good seal.

You might want more than one layer but generally not more than two or three. If you are using drastically different materials, such as copper or brass to PVC, you may need extra but that is unlikely. Too much tape is as bad as too little. It will prevent a good seal. With the proper amount the pipe should thread together smoothly, sealing all gaps in the thread.

When do you not use plumber’s tape?

This tape is only effective on tapered threads as it uses compression to form the seal. Fortunately, the vast majority of the connections you make in irrigation will be with National Pipe Thread Tapered Thread, or NPT, and this tape will work well.

Many will tell you that brass to brass fittings are self sealing. In one manner they are but it takes an experienced professional to know which ones will work. You risk a leak if you are not sure you have the correct condition. Tape is cheap insurance. Brass fitting threads also tend to be extra sharp, especially on the smaller pieces, and may cut through the tape and ruin the seal. In this extra care is needed. In extreme cases you might need pipe dope but that is rare. The general connection involving brass in an irrigation system is with the backflow. Plumbers tape should work just fine there.

Mar 5 2012

Pump Installation for Irrigation

Ok. The water is in the lake and you want it on your yard. This means you need a pump to move the water from the lake to your irrigation system. Choosing the pump is addressed in another article. We’ll talk about how you put it in and what you need to do it. Pumping from a well is the same basic procedure.

Basically we will have a pipe, probably PVC, going down into your water supply, up through a pump and into your system. So let’s start with the pipe and the water. If you are lucky you have lots of fish in your lake. Unfortunately, you also have sediment, plants, bugs and other things that will not go through your sprinkler heads. The first thing to install is some sort of filter/strainer. It fits on the end of the pipe and keeps the larger trash out.

Foot Valve

One type of filter is a foot valve. This is a combination of a filter and a check valve. A foot valve keeps the water in the pipe even when the pump is turned off. This means that the pump is kept wet (primed) and water is at the pump as soon as you turn it on. If water ran back down to the lake the pump would only have air to pull. This is an example of a foot valve and strainer combination. They can be PVC, aluminum, brass or steel.

Basket Strainer

Some other options are a basket strainer or a self-cleaning strainer. If you use either one of these, you will need a check valve, too, or the pump will not stay primed. The exception to this is if you have a self-priming pump. A basket strainer or self-cleaning strainer is all you need then.

Now we have PVC pipe running up hill to the pump. The end in the water must be secured to something: dock, pier, post, etc. It cannot float free or it will break. The size of the PVC will be determined by your pump. For both looks and freeze protection you might want to bury the pipe. If you leave it above ground you will need to stake it down and possibly insulate to protect from freezing.

The pump itself will need to be bolted to a concrete slab and connected to your pump switch and controller.

So what do we need and why?

At the pipe end/strainer:

To fasten to a post:

Galvanized strapping

Strapping. Usually galvanized, available at almost any hardware store. Available in rolls or pre-cut to length.
Nails, should be galvanize, 16p.
Claw hammer.
Tin snips to cut strap.
Leather gloves and eye protection

To fasten strainer/foot valve to pipe:

Drill, preferably cordless
Good, grounded extension cord if your drill is not cordless
Assorted drill bits
Phillips and/or slotted screwdriver
DO NOT PUT THE EXTENSION CORD IN THE WATER. Please don’t.

For the PVC:

Primer and cement
Hacksaw
Pipe tape (commonly called Teflon tape, even though it’s not)
Saw horses or cinderblock to lift pipe off ground while cutting.
Pipe and fittings, determined by pump and location
Tape measure. Measure everything twice. Trust me.
If placed above ground you will need some sort of stakes to hold the pipe in place

For the Pump:

The pump needs to be bolted down to a slab. If possible, buy one pre-made. If you need to make one follow factory recommendations and you will need:

Board 1”x4: to length for framing.
Saw, hand or power
Hammer for nails and stakes
1”x2”x12” stakes
8p or 10p nails. Duplex/double head are best
Wire mesh or #3 rebar re-inforcing for concrete. Some stores sell pre-cut.
24” bolt cutters if you have to cut your own rebar
Tie wire (also known as baling wire) if you tie your own rebar
Pliers, preferably side cutters.
Bags of concrete for slab
Something to mix concrete in: bucket, wheelbarrow, etc.
Bolts to mound pump to concrete. See factory recommendations.

Miscellaneous:

A bucket or hose to put water in the pump to prime and to mix the concrete
Shovel for digging ditch and mixing concrete
Rags
Wire nuts
And if you are like me, a first aid kit.

Sprinkler Warehouse

Irrigation & Lawn Sprinkler System Answers!

Category Archives: Irrigation Installation

Now You See it, Now You…Wait! Where Did it Go?

Designed to Fail? Ooops…

Valve Manifolds and Why You Want Them

Why Just Florida?

The Right Way to Assemble and Glue PVC Pipe

Watering Trees

How to Identify the Size of the Water Meter & Supply Line

Want to Have an Impact?

Teflon Tape and How To Use It

Pump Installation for Irrigation

Follow “Sprinkler Warehouse”