Comments on: Have A Question?

By: Gator Guy

Gator Guy — Mon, 21 May 2012 14:25:48 +0000

Your best bet might be to convert to drip. Look at http://www.sprinklerwarehouse.com/Drip-Emitters-s/131.htm for some different emitters.
If you don’t want to go that way, look at http://www.sprinklerwarehouse.com/Rain-Bird-SQ-Series-Nozzles-s/8405.htm, fairly low flow.
Or try http://www.sprinklerwarehouse.com/Hunter-Sprinkler-Rotator-Nozzle-p/mplcs515.htm. Left corner shown but they come in left, right and center. They can be dialed back to fit fairly close to your design. Again, lower flow.

If you have time post this question on http://www.sprinklertalk.com. A number of experts across the country are involved in that forum and will help with any problems.

By: David

David — Sun, 20 May 2012 23:30:59 +0000

I have a small flower garden area which is about 3 1/2 feet wide and 8ft long, I have an existing irrigation system in the garden but the heads put out too much water. Is there a nozzle I can use on the 18 inch risers that are currently there?

By: Gator Guy

Gator Guy — Mon, 14 May 2012 19:11:20 +0000

I’m sorry. We have never carried such a system. I’m afraid we don’t have any more knowledge of suppliers than you might.

By: Gator Guy

Gator Guy — Mon, 14 May 2012 19:10:00 +0000

It’s one of those things where IN THEORY it can be done. All you are doing is completing a circuit. In practice the few times I’ve heard of it being installed it failed. No one ever came back with a reason why.

By: Lillian Jerman

Lillian Jerman — Thu, 10 May 2012 16:37:18 +0000

Hello! Hope you can help me. I’m looking for a portaable 3 in 1 sprinkler system.
18′ hose has 3 in line sprinkler heads. Ann Jerman May 10, 2012

By: Marvin Rains

Marvin Rains — Tue, 08 May 2012 19:32:24 +0000

I checked that. Both were not set to anything. I also made sure that the dial was not set on cycle. I think that I will set the run times to half what I want and just let it run twice.

By: alejandro martinez g

alejandro martinez g — Mon, 07 May 2012 19:28:18 +0000

i am installing a irrrigation system with 2 controllers hunter x core a 4 zones and a 6 zones in a house and im am trying to install a wss sensor the controllers are no more than 50 meters away one from the other so i think i can install one sensor to work with both controllers, am i ok with this idea?

By: Gator Guy

Gator Guy — Mon, 07 May 2012 16:11:45 +0000

See if it has more than one program (A, B, C etc.) The problem you describe is usually caused by having the same program on B that it does on A. So A runs, stops, and B kicks in.

By: Gator Guy

Gator Guy — Mon, 07 May 2012 16:10:25 +0000

You probably can’t. They are solid state and there are very few repair stations. Call 760-591-7383 for Hunter support or go to http://www.hunterindustries.com/support/email_support/email to email them.

By: Marvin Rains

Marvin Rains — Mon, 07 May 2012 13:45:13 +0000

I have a Signature 12 station controller that repeats its cycle every time it waters. (It goes through every station and then goes through them again). this leaves the area too wet. How do I stop this?